Juniper JN0-683 Study Guide Archives Updated on Jul 19, 2025
Download JN0-683 Mock Test Study Material
NEW QUESTION # 11
Which parameter is used to associate a received route with a local VPN route table?
- A. VNI
- B. VLAN ID
- C. route-target community
- D. route-distinguisher
Answer: C
Explanation:
* Understanding VPN Route Table Association:
* In MPLS/VPN and EVPN networks, theroute-target communityis a BGP extended community attribute used to control the import and export of VPN routes. It associates received routes with the appropriate VPN route tables on the PE (Provider Edge) routers.
* Function of Route-Target Community:
* The route-target community tag ensures that routes are imported into the correct VRF (Virtual Routing and Forwarding) instance, allowing them to be correctly routed within the VPN.
Conclusion:
* Option A:Correct-The route-target community is used to associate received routes with a local VPN route table.
NEW QUESTION # 12
You are asked to implement VXLAN group-based policies (GBPs) in your data center. Which two statements are correct in (his scenario? (Choose two.)
- A. VXLAN GBP ensures consistent application of BGP groups throughout the network.
- B. VXLAN GBP uses scalable group tags thatmust be configured statically on each switch and activated through 802.1X.
- C. VXLAN GBP ensures consistent application of security group policies throughout the network.
- D. VXLAN GBP uses scalable group tags that may be configured on a RADIUS server and pushed to the switch through 802.1X.
Answer: C,D
Explanation:
* VXLAN Group-Based Policies (GBP):
* VXLAN Group-Based Policies are used to apply security policies consistently across the network. These policies are often tied to user or device identities rather than static IP addresses, which allows for more dynamic and scalable security management.
* Scalable Group Tags via RADIUS and 802.1X:
* Option B:VXLAN GBP can use scalable group tags configured on a RADIUS server, which are then pushed to network devices through 802.1X. This allows for centralized and automated policy application based on user or device identity.
* Consistent Security Policy Application:
* Option C:GBP ensures that security policies are consistently applied across the network, regardless of where a user or device connects. This consistency is crucial in environments where security policies must follow the user or device.
Conclusion:
* Option B:Correct-Group tags can be configured on a RADIUS server and pushed via 802.1X, enabling centralized policy management.
* Option C:Correct-GBP ensures consistent application of security policies, which is essential for maintaining security across a dynamic network environment.
NEW QUESTION # 13
Exhibit.
Host A is connected to vlan 100 on lead. Host B is connected to vlan 200 on leaf1. Host A and Host B ate unable to communicate. You have reviewed the touting and your hosts have the correct default route (.1) Referring to the exhibit, which two commands will solve the problem? (Choose two.)
- A. set vlans vn10013-interface irb.100
- B. set interfaces irb unit 100 family inet address 192-168.100.1
- C. set routing-options static route 0.0.0.0/0 next-hop 192.168.200.10
- D. delete vlans vn200 13-interface irb.200
Answer: A,C
Explanation:
In the provided network configuration, Host A is in VLAN 100 and Host B is in VLAN 200. The issue arises because these two hosts are unable to communicate, which indicates that either the interfaces are not properly linked to their respective VLANs, or there is a missing static route required for inter-VLAN routing.
Step-by-Step Analysis:
* VLAN Assignment:
* The exhibit shows that irb.200 is correctly associated with VLAN 200 in the configuration.
However, there is no corresponding irb.100 for VLAN 100. Without irb.100, the network lacks the logical interface to handle routing for VLAN 100. Thus, adding irb.100 to VLAN 100 is necessary.
Command to solve this:
set vlans vn100 13-interface irb.100
* Static Route Configuration:
* For inter-VLAN routing to occur, a static route needs to be configured that allows traffic to pass between different subnets (in this case, between VLAN 100 and VLAN 200). The command set routing-options static route 0.0.0.0/0 next-hop 192.168.200.10 would add a static route that directs all traffic from VLAN 100 to the correct gateway (192.168.200.10), which is necessary to route traffic between the two VLANs.
Command to solve this:
set routing-options static route 0.0.0.0/0 next-hop 192.168.200.10
Explanation of Incorrect Options:
* Option A (delete vlans vn200 13-interface irb.200): This would remove the logical interface associated with VLAN 200, which is not desired because we need VLAN 200 to remain active and properly routed.
* Option B (set interfaces irb unit 100 family inet address 192-168.100.1): This command would incorrectly assign an IP address that does not correspond with the subnet of VLAN 100 (192.168.200.1
/24). This could create a misconfiguration, leading to routing issues.
Data Center References:
For a Data Center, proper VLAN management and static routing are crucial for ensuring that different network segments can communicate effectively, especially when dealing with separated subnets or zones like in different VLANs. This aligns with best practices in DCIM (Data Center InfrastructureManagement) which stress the importance of proper network configuration to avoid downtime and ensure seamless communication between all critical IT infrastructure components.
Ensuring that the correct interfaces are associated with the correct VLANs and having the proper static routes in place are both essential steps in maintaining a robust and reliable data center network.
This detailed analysis reflects best practices as noted in standard data center design and network configuration guides.
NEW QUESTION # 14
You are deploying an IP fabric with an oversubscription ratio of 3:1.
In this scenario, which two statements are correct? (Choose two.)
- A. The oversubscription ratio remains the same when you add leaf devices.
- B. The oversubscription ratio decreases when you add leaf devices.
- C. The oversubscription ratio increases when you remove leaf devices.
- D. The oversubscription ratio remains the same when you remove leaf devices.
Answer: A,C
Explanation:
* Understanding Oversubscription Ratio in IP Fabrics:
* The oversubscription ratio in an IP fabric typically refers to the ratio of the available bandwidth at the edge of the network (leaves) to the available bandwidth at the core or spine. A 3:1 oversubscription ratio means that for every 3 units of bandwidth at the leaves, there is 1 unit of bandwidth at the spine.
* Impact of Adding or Removing Leaf Devices:
* Removing Leaf Devices:When you remove leaf devices, the amount of total edge bandwidth decreases while the bandwidth in the spine remains constant. This causes the oversubscription ratio toincreasebecause there is now less total bandwidth to distribute across the same amount of spine bandwidth.
* Adding Leaf Devices:Conversely, when you add leaf devices, the total edge bandwidth increases. Since the spine bandwidth remains the same, the oversubscription ratio would remain the same if the additional leaves consume their share of the available bandwidth proportionally.
Conclusion:
* Option C:Correct-Removing leaf devices increases the oversubscription ratio.
* Option D:Correct-Adding leaf devices typically maintains the oversubscription ratio assuming uniform bandwidth distribution.
NEW QUESTION # 15
You want to provide a OCI that keeps each data center routing domain isolated, while also supporting translation of VNIs. Which DCI scheme allows these features?
- A. MPLS DCI label exchange
- B. over the top (OTT) with VNI translation enabled
- C. over the top (OTT) with proxy gateways
- D. VXLAN stitching
Answer: D
Explanation:
* Understanding DCI (Data Center Interconnect) Schemes:
* DCI schemes are used to connect multiple data centers, enabling seamless communication and resource sharing between them. The choice of DCI depends on the specific requirements, such as isolation, VNI translation, or routing domain separation.
* VXLAN Stitching:
* VXLAN stitching involves connecting multiple VXLAN segments, allowing VNIs (VXLAN Network Identifiers) from different segments to communicate with each other while maintaining separate routing domains.
* This approach is particularly effective for keeping routing domains isolated while supporting VNI translation, making it ideal for scenarios where you need to connect different data centers or networks without merging their control planes.
* Other Options:
* A. MPLS DCI label exchange:This option typically focuses on MPLS-based interconnections and does not inherently support VNI translation or isolation in the context of VXLAN.
* B. Over the top (OTT) with VNI translation enabled:This could support VNI translation but does not inherently ensure routing domain isolation.
* D. Over the top (OTT) with proxy gateways:This typically involves using external gateways for traffic routing and may not directly support VNI translation or isolation in the same way as VXLAN stitching.
Data Center References:
* VXLAN stitching is a powerful method in multi-data center environments, allowing for flexibility in connecting various VXLAN segments while preserving network isolation and supporting complex interconnect requirements.
NEW QUESTION # 16
Which three statements are correct about VXLAN control planes? (Choose three.)
- A. EVPN is inefficient and does not scale well.
- B. Both multicast and EVPN can facilitate MAC learning.
- C. EVPN enables fast convergence and updates.
- D. Multicast does not require as many resources.
- E. Multicast is not agile and requires manual VNI mapping.
Answer: B,C,D
Explanation:
* VXLAN Control Planes:
* VXLAN (Virtual Extensible LAN) uses different control planes to handle MAC learning and traffic forwarding. The control planes include multicast and EVPN (Ethernet VPN).
* Multicast and EVPN Comparison:
* Option B:Both multicast and EVPN can be used for MAC learning in a VXLAN environment.
Multicast is a more traditional approach, while EVPN is more advanced and supports distributed MAC learning.
* Option D:EVPN offers benefits such as fast convergence and rapid updates, making it more efficient and scalable for modern data center environments.
* Option E:Multicast does not require as many resources because it relies on traditional Layer 3 multicast mechanisms to distribute broadcast, unknown unicast, and multicast (BUM) traffic.
However, it can be less flexible and less scalable compared to EVPN.
Conclusion:
* Option B:Correct-Both control planes facilitate MAC learning.
* Option D:Correct-EVPN provides fast convergence and updates.
* Option E:Correct-Multicast is resource-efficient but less flexible.
NEW QUESTION # 17
Exhibit.
Referring to the exhibit, when Host A sends an ARP request for Host B's IP address, which Junos feature does leaf1require to send an ARP response back to Host A without having to send a broadcast frame over the fabric?
- A. GARP
- B. proxy ARP
- C. proxy NDP
- D. DAD
Answer: B
Explanation:
* Scenario Overview:
* In the exhibit, Host A is trying to resolve Host B's IP address (10.10.1.2) through ARP (Address Resolution Protocol). Normally, an ARP request would be broadcasted over the network, and the host owning the IP address (Host B) would respond.
* Role of Proxy ARP:
* Option A:Proxy ARPallows a router or switch (in this case, leaf1) to respond to ARP requests on behalf of another host. Leaf1, knowing the MAC address of Host B through the EVPN MAC advertisement, can reply to Host A's ARP request directly without broadcasting the request across the entire network fabric. This feature reduces unnecessary traffic and increases network efficiency.
Conclusion:
* Option A:Correct-Proxy ARP enables leaf1 to respond to Host A's ARP request for Host B's IP without broadcasting over the IP fabric, thus providing the ARP response locally.
NEW QUESTION # 18
Exhibit.
Connections between hosts connected to Leaf-1 and Leaf-2 are not working correctly.
- A. Referring to the exhibit, which two configuration changes are required to solve the problem? (Choose two.)
- B. Configure the setswitch-options service-id 1 parameter on Leaf-2.
- C. Configure the setswitch-options route-distinguisher i92.168.100.50:i parameter on Leaf-1.
- D. Configure the set switch-options vrf-target target:65000:l parameteron Leaf-2.
- E. Configure the setswitch-options vtep-source-interface irb.0parameter on Leaf-1.
Answer: B,D
Explanation:
* Issue Analysis:
* The problem in the exhibit suggests a mismatch in configuration parameters between Leaf-1 and Leaf-2, leading to communication issues between hosts connected to these leaf devices.
* Configuration Mismatches:
* Service-ID:Leaf-1 has service-id 1 configured, while Leaf-2 does not have this parameter. For consistency and proper operation, the service-id should be the same across both leaf devices.
* VRF Target:Leaf-1 is configured with vrf-target target:65000:1, while Leaf-2 is configured with vrf-target target:65000:2. To allow proper VRF import/export between the two leafs, these should match.
* Corrective Actions:
* C. Configure the set switch-options vrf-target target:65000:1 parameter on Leaf-2:This aligns the VRF targets between the two leaf devices, ensuring they can correctly import and export routes.
* E. Configure the set switch-options service-id 1 parameter on Leaf-2:This ensures that both Leaf-1 and Leaf-2 use the same service ID, which is necessary for consistency in the EVPN- VXLAN setup.
Data Center References:
* Correct configuration of VRF targets and service IDs is critical in EVPN-VXLAN setups to ensure that routes and services are correctly shared and recognized between different devices in the network fabric.
NEW QUESTION # 19
Which two statements are correct about an IP fabric? (Choose two.)
- A. FBGP is only required to route mostrouting information to external devices outside the fabric.
- B. The multipath multiple-as statement is required to enable ECMP if every device has a different AS number.
- C. Only a single point to point EBGP session is required between peers in an IP fabric.
- D. All leaf devices can use the same AS number in an IP fabric without making any adjustments to the EBGP configuration
Answer: B,D
Explanation:
* BGP in IP Fabric:
* In an IP fabric, Border Gateway Protocol (BGP) is used to manage the routing between leaf and spine devices. Each device can have the same or different Autonomous System (AS) numbers depending on the network design.
* Multipath Multiple-AS:
* Option B:If every device in the fabric has a different AS number, then enabling Equal-Cost Multi-Path (ECMP) routing requires the multipath multiple-as statement. This configuration allows BGP to consider multiple paths across different AS numbers as equal cost, enabling efficient load balancing across the network.
* Same AS Number Configuration:
* Option A:It's possible for all leaf devices to use the same AS number in an IP fabric, which simplifies the configuration. EBGP (External BGP) will still function correctly in this setup because BGP considers the peering relationship rather than strictly enforcing different AS numbers in this specific use case.
Conclusion:
* Option B:Correct-This statement is essential for enabling ECMP in a multi-AS environment.
* Option A:Correct-Leaf devices can share the same AS number without needing special EBGP configuration.
NEW QUESTION # 20
You are asked to interconnect two of your company's data centers across an IP backbone. Both data centers require Layer 2 and Layer 3 connectivity. In this scenario, which three actions would accomplish this task?
(Choose three.)
- A. Ensure there is a full mesh of VTEPs between all leaf nodes within data centers.
- B. Advertise Type 2 EVPN routes across the DCI.
- C. Ensure border leaf nodes in each data center can exchange EVPN routes.
- D. Advertise Type 5 EVPN routes across the DCI.
- E. Ensure there is a full mesh of VTEPs between all spine nodes within both data centers.
Answer: B,C,D
Explanation:
* Layer 2 and Layer 3 Connectivity Requirements:
* To interconnect two data centers across an IP backbone with both Layer 2 (L2) and Layer 3 (L3) connectivity, EVPN-VXLAN (Ethernet VPN with Virtual Extensible LAN) is the ideal solution.
EVPN supports L2 VPNs while also enabling L3 connectivity across multiple locations.
* Necessary EVPN Route Types:
* Type 2 EVPN Routes:These routes are used to advertise MAC addresses for Layer 2 connectivity. They are essential for enabling seamless L2 communication across data centers.
* Type 5 EVPN Routes:These routes are necessary for advertising IP prefixes for Layer 3 connectivity between data centers. They enable the exchange of L3 information across the IP backbone, ensuring routed traffic can reach its destination.
* Border Leaf Nodes:
* Border Leaf Nodes:Ensuring that the border leaf nodes (the entry and exit points for traffic between data centers) can exchange EVPN routes is critical for the correct dissemination of both L2 and L3 information across the data centers.
Conclusion:
* Option A:Correct-Type 2 EVPN routes are required for Layer 2 MAC address learning and communication across the DCI (Data Center Interconnect).
* Option B:Correct-Border leaf nodes need to exchange EVPN routes to maintain connectivity between data centers.
* Option D:Correct-Type 5 EVPN routes are essential for Layer 3 connectivity across the DCI.
OptionsCandEare incorrect because they refer to establishing full mesh VTEPs (VXLAN Tunnel Endpoints) across all spine or leaf nodes, which is unnecessary for the scenario provided. The focus should be on border leaf nodes and appropriate route advertisements for L2 and L3 connectivity.
NEW QUESTION # 21
A local VTEP has two ECMP paths to a remote VTEP
Which two statements are correctwhen load balancing is enabled in this scenario? (Choose two.)
- A. The inner packet fields are used in the hash for load balancing.
- B. The destination port in the UDP header is used to load balance VXLAN traffic.
- C. The source port in the UDP header is used to load balance VXLAN traffic.
- D. The inner packet fields are not used in the hash for load balancing.
Answer: A,C
Explanation:
* Load Balancing in VXLAN:
* VXLAN uses UDP encapsulation to transport Layer 2 frames over an IP network. For load balancing across Equal-Cost Multi-Path (ECMP) links, various fields in the packet can be used to ensure even distribution of traffic.
* Key Load Balancing Fields:
* C. The source port in the UDP header is used to load balance VXLAN traffic:This is correct.
The source UDP port in the VXLAN packet is typically calculated based on a hash of the inner packet's fields. This makes the source port vary between packets, enabling effective load balancing across multiple paths.
* D. The inner packet fields are used in the hash for load balancing:This is also correct. Fields such as the source and destination IP addresses, source and destination MACaddresses, and possibly even higher-layer protocol information from the inner packet can be used to generate the hash that determines the ECMP path.
* Incorrect Statements:
* A. The inner packet fields are not used in the hash for load balancing:This is incorrect as the inner packet fields are indeed critical for generating the hash used in load balancing.
* B. The destination port in the UDP header is used to load balance VXLAN traffic:This is incorrect because the destination UDP port in VXLAN packets is typically fixed (e.g., port 4789 for VXLAN), and therefore cannot be used for effective load balancing.
Data Center References:
* Effective load balancing in VXLAN is crucial for ensuring high throughput and avoiding congestion on specific links. By using a combination of the source UDP port and inner packet fields, the network can distribute traffic evenly across available paths.
NEW QUESTION # 22
Which statement is correct about a collapsed fabric EVPN-VXLAN architecture?
- A. Fully meshed back-to-back links are needed between the spine devices.
- B. Using Virtual Chassis at the leaf layer increases resiliency.
- C. Border gateway functions occur on border leaf devices.
- D. It supports multiple vendors in the fabric as long as all the spine devices are Juniper devices deployed with L2 VTEPs
Answer: C
Explanation:
* Collapsed Fabric Architecture:
* A collapsed fabric refers to a simplified architecture where the spine and leaf roles are combined, often reducing the number of devices and links required.
* In this architecture, the spine typically handles core switching, while leaf switches handle both access and distribution roles.
* Understanding Border Gateway Functionality:
* Border gateway functions include connecting the data center to external networks or other data centers.
* In a collapsed fabric, these functions are usually handled at the leaf level, particularly on border leaf devices that manage the ingress and egress of traffic to and from the data center fabric.
* Correct Statement:
* D. Border gateway functions occur on border leaf devices:This is accurate in collapsed fabric architectures, where the border leaf devices take on the role of managing external connections and handling routes to other data centers or the internet.
Data Center References:
* The collapsed fabric model is advantageous in smaller deployments or scenarios where simplicity and cost-effectiveness are prioritized. It reduces complexity by consolidating functions into fewer devices, and the border leaf handles the critical task of interfacing with external networks.
In conclusion, border gateway functions are effectively managed at the leaf layer in collapsed fabric architectures, ensuring that the data center can communicate with external networks seamlessly.
NEW QUESTION # 23
You are deploying a new network lo support your Al workloads on devices that support at least 400 Gbps Ethernet. There is no requirement for any Layer 2 VLANs in this network. Which network architecture would satisfy this requirement?
- A. an IP fabric using EBGP
- B. an IP fabric with an EVPN-VXLAN architecture
- C. an IP fabric using the EVPN-MPLS architecture
- D. an IP fabric using PIM-SM to signal VXLAN overlay
Answer: A
Explanation:
* Requirements for AI Workloads:
* The scenario requires a network that supports at least 400 Gbps Ethernet and does not require Layer 2 VLANs. This setup is well-suited for a pure Layer 3 network, which can efficiently route traffic between devices without the overhead or complexity of maintaining Layer 2 domains.
* Choosing the Right Network Architecture:
* Option D:An IP fabric using EBGP (External BGP) is ideal for this scenario. In a typical IP fabric, EBGP is used to handle routing between spine and leaf switches, creating a scalable and efficient network. Since there is no need for Layer 2 VLANs, the pure IP fabric design with EBGP provides a straightforward and effective solution.
* Options A, B, and Cinvolve more complex architectures (like VXLAN or EVPN), which are unnecessary when there's no requirement for Layer 2 overlays or VLANs.
Conclusion:
* Option D:Correct-An IP fabric with EBGP is the most suitable and straightforward architecture for a network that needs to support high-speed AI workloads without Layer 2 VLANs.
NEW QUESTION # 24
Which three statements are correct about symmetric IRB routing with EVPN Type 2 routes? (Choose three.)
- A. Symmetric routing supports the EVPN service VLAN bundle.
- B. Symmetric routing requires MAC-VRF.
- C. An L3 interface (IRB) is required for each local VLAN.
- D. Symmetric routing is less efficient than asymmetric routing.
- E. Symmetric routing requires an extra transit VNI for each VRF.
Answer: B,C,E
Explanation:
* Symmetric IRB Routing with EVPN Type 2 Routes:
* Symmetric Routing: In symmetric IRB (Integrated Routing and Bridging), routing occurs in both directions at the ingress and egress leaf nodes using the same routing logic. This is contrasted with asymmetric routing, where different routing logic is used depending on the direction of the traffic.
* Required Components:
* Option A:An L3 IRB interface is necessary for each VLAN that participates in routing, as it handles the Layer 3 processing for the VLAN.
* Option B:MAC-VRF is required for symmetric routing to maintain a mapping of MAC addresses to the appropriate VRF, ensuring correct forwarding within the EVPN.
* Option D:A transit VNI (Virtual Network Identifier) is required for each VRF to encapsulate the Layer 3 traffic as it traverses the network, allowing the IP traffic to be appropriately forwarded.
Conclusion:
* Option A:Correct-Each local VLAN needs an IRB interface for L3 processing.
* Option B:Correct-MAC-VRF is necessary for handling MAC address resolution in symmetric routing.
* Option D:Correct-Transit VNIs are required for routing VRF-specific traffic across the network.
OptionsCandEare incorrect because:
* C:Symmetric routing can work with various VLAN models, including single or multiple VLANs within an EVPN instance.
* E:Symmetric routing is generally more efficient than asymmetric routing as it uses consistent routing logic in both directions.
NEW QUESTION # 25
Your organization is implementing EVPN-VXLAN and requires multiple overlapping VLAN-IDs. You decide to use a routing-instance type mac-vrf to satisfy this request.
Which two statements are correct in this scenario? (Choose two.)
- A. Spine-facing interfaces must be configured using an enterprise-styleconfiguration.
- B. The routing-instance service type can be VLAN-based.
- C. Host-facing interfaces must be configured using a service-provider style configuration.
- D. Host-facing interfaces must be configured using enterprise-style configuration.
Answer: B,C
Explanation:
* Understanding the Scenario:
* EVPN-VXLAN deployments often involve scenarios where multiple tenants or applications require overlapping VLAN IDs, which can be managed using the mac-vrf routing instance type.
This allows you to segregate traffic within the same VLAN ID across different tenants.
* Host-facing Interface Configuration:
* A. Host-facing interfaces must be configured using a service-provider style configuration:
This is correct. In mac-vrf configurations, host-facing interfaces (those connecting end devices) typically follow a service-provider style configuration, where each customer or tenant's traffic is isolated even if overlapping VLAN IDs are used.
* B. Host-facing interfaces must be configured using enterprise-style configuration:This is incorrect for mac-vrf instances because enterprise-style configurations are more common in simpler, less segmented networks.
* Routing Instance Service Type:
* D. The routing-instance service type can be VLAN-based:This is correct. The service type in mac-vrf can indeed be VLAN-based, which is particularly useful in scenarios where VLAN ID overlap is needed between different tenants or services.
Data Center References:
* The mac-vrf instance type is powerful for handling complex multi-tenant environments in EVPN- VXLAN, especially when dealing with overlapping VLAN IDs across different segments of the network.
NEW QUESTION # 26
Exhibit.
Referring tothe exhibit, which statement is correct?
- A. The MAC address is unknown and not in the forwarding table of the remote VTEP.
- B. The remote VTEP is not responding.
- C. VNI 100 is not configured on the remote VTEP.
- D. The MAC address is known but not reachable by the remote VTEP
Answer: A
Explanation:
* Analyzing the Exhibit Output:
* The command ping overlay tunnel-type vxlan is used to test the VXLAN tunnel between two VTEPs (VXLAN Tunnel Endpoints). The output shows a warning about missing hash parameters, but more importantly, it displays the result: End-System Not Present.
* Understanding the Response:
* The message End-System Not Present indicates that the remote VTEP (192.168.2.20) did not find the MAC address 00:00:5E:00:53:CC in its forwarding table. This typically means that the MAC address is unknown to the remote VTEP, and as a result, it could not forward the packet to the intended destination.
Conclusion:
* Option B:Correct-The MAC address is unknown and is not in the forwarding table of the remote VTEP, which is why the system reports that the "End-System" is not present.
NEW QUESTION # 27
Exhibit.
You have implemented an EVPN-VXLAN data center. Device served must be able to communicate with device server2.
Referring to the exhibit, which two statements are correct? (Choose two.)
- A. An IRB Interface must be configured on leaf1 and Ieaf2.
- B. An IRB interface must be configured on spinel and spine2.
- C. Traffic from server! to server2 will transit the VXLAN tunnel between leaf1 and Ieaf2.
- D. Traffic from server1 to server2 will transit a VXLAN tunnel to spinel or spine2. then a VXLAN tunnel from spinel or spine2 to Ieaf2.
Answer: A,C
Explanation:
* Understanding the Exhibit Setup:
* The network diagram shows an EVPN-VXLAN setup, a common design for modern data centers enabling Layer 2 and Layer 3 services over an IP fabric.
* Leaf1 and Leaf2 are the leaf switches connected to Server1 and Server2, respectively, with each server in a different subnet (172.16.1.0/24 and 172.16.2.0/24).
* Spine1 and Spine2 are part of the IP fabric, interconnecting the leaf switches.
* EVPN-VXLAN Basics:
* EVPN (Ethernet VPN) provides Layer 2 and Layer 3 VPN services using MP-BGP.
* VXLAN (Virtual Extensible LAN) encapsulates Layer 2 frames into Layer 3 packets for transmission across an IP network.
* VTEP (VXLAN Tunnel Endpoint) interfaces on leaf devices handle VXLAN encapsulation and decapsulation.
* Integrated Routing and Bridging (IRB):
* IRB interfaces are required on leaf1 and leaf2 (where the endpoints are directly connected) to route between different subnets (in this case, between 172.16.1.0/24 and 172.16.2.0/24).
* The IRB interfaces provide the necessary L3 gateway functions for inter-subnet communication.
* Traffic Flow Analysis:
* Traffic from Server1 (172.16.1.1) destined for Server2 (172.16.2.1) must traverse from leaf1 to leaf2.
* The traffic will be VXLAN encapsulated on leaf1, sent over the IP fabric, and decapsulated on leaf2.
* Since the communication is between different subnets, the IRB interfaces on leaf1 and leaf2 are crucial for routing the traffic correctly.
* Correct Statements:
* C. An IRB Interface must be configured on leaf1 and leaf2:This is necessary to perform the inter-subnet routing for traffic between Server1 and Server2.
* D. Traffic from server1 to server2 will transit the VXLAN tunnel between leaf1 and leaf2:
This describes the correct VXLAN operation where the traffic is encapsulated by leaf1 and decapsulated by leaf2.
Data Center References:
* In EVPN-VXLAN architectures, the leaf switches often handle both Layer 2 switching and Layer 3 routing via IRB interfaces. This allows for efficient routing within the data center fabric without the need to involve the spine switches for every routing decision.
* The described traffic flow aligns with standard EVPN-VXLAN designs, where direct VXLAN tunnels between leaf switches enable seamless and scalable communication across a data center network.
NEW QUESTION # 28
You are asked to identify microburst traffic occurring in the network leading lo packet drops in your data center switches Which two tools would be used in this scenario? (Choose two.)
- A. port mirroring
- B. Traceoptions
- C. port buffer monitoring
- D. syslog
Answer: A,C
Explanation:
* Identifying Microburst Traffic:
* Microbursts are short spikes in network traffic that can overwhelm buffers and cause packet drops. Detecting and analyzing microbursts is crucial for understanding where packet loss might be occurring in a data center network.
* Port Buffer Monitoring:
* Port Buffer Monitoring:This tool specifically tracks the usage of switch buffers, helping to identify when microbursts are causing buffers to overflow, leading to packet drops.
* Port Mirroring:
* Port Mirroring:This tool allows you to monitor real-time traffic on a specific port by copying the traffic to another port where it can be analyzed, often with a packet analyzer. While port mirroring doesn't directly detect microbursts, it helps capture traffic patterns that can indicate microbursts.
Conclusion:
* Option C:Correct-Port buffer monitoring directly identifies buffer overflows caused by microbursts.
* Option A:Correct-Port mirroring allows for the detailed capture and analysis of traffic patterns, which can reveal microburst behavior.
Options B(Traceoptions) andD(Syslog) are less effective in identifying microburst traffic. Traceoptions focus on control plane traffic debugging, and Syslog is more about logging system events than detecting high- frequency traffic spikes.
NEW QUESTION # 29
You are asked to deploy 100 QFX Series devices using ZTP Each OFX5120 requires a different configuration. In this scenario, what are two components that you would configure on the DHCP server?
(Choose two.)
- A. the management IP address for each OFX5120
- B. the MAC address for each OFX5120
- C. the IP address of the FTP server
- D. the MAC address of the FTP server
Answer: A,B
Explanation:
* Zero Touch Provisioning (ZTP):
* ZTP allows for the automated configuration of network devices, like QFX Series switches, without manual intervention. During ZTP, a switch will obtain its configuration from a DHCP server and then download the required software and configuration files from a specified server (e.
g., FTP, HTTP).
* DHCP Server Configuration:
* Option B:The DHCP server needs to know theMAC address for each QFX5120to provide a specific configuration based on the device identity. By mapping the MAC address to a particular configuration, the DHCP server can ensure that each switch gets the correct configuration.
* Option D:Themanagement IP address for each QFX5120must also be assigned by the DHCP server. This IP address allows the device to communicate on the network and access the configuration files and other required resources during the ZTP process.
Conclusion:
* Option B:Correct-MAC addresses allow the DHCP server to identify each QFX5120 and assign the appropriate configuration.
* Option D:Correct-Management IP addresses are essential for network communication during ZTP.
NEW QUESTION # 30
You are asked to deploy 100 QFX Series devices using ZTP Each OFX5120 requires a different configuration. In this scenario, what are two components that you would configure on the DHCP server?
(Choose two.)
- A. the management IP address for each OFX5120
- B. the MAC address for each OFX5120
- C. the IP address of the FTP server
- D. the MAC address of the FTP server
Answer: A,B
NEW QUESTION # 31
Why is a designated forwarder required in a multihomed CE-to-PE VXLAN environmentusing EVPN signalling?
- A. The designated forwarder is required to prevent duplicate packets from being received on multihomed hosts.
- B. The designated forwarder is required to prevent flooding of MAC addresses to multihomed hosts.
- C. The designated forwarder is required to prevent a traffic storm from being received on multihomed hosts.
- D. The designated forwarder is required to prevent packets from looping between the PEs.
Answer: A
Explanation:
* Understanding Multihomed CE-to-PE VXLAN Environment:
* In a VXLAN environment using EVPN signaling, multiple PEs (Provider Edge devices) can be connected to the same CE (Customer Edge device). This setup is referred to as multihoming, where a CE device has multiple connections to the network to ensure redundancy and load balancing.
* Role of the Designated Forwarder:
* The designated forwarder (DF) is a mechanism used in EVPN to manage the forwarding of broadcast, unknown unicast, and multicast (BUM) traffic in a multihomed environment. The DF is selected to ensure that only one of the PEs forwards this type of traffic to the CE, preventing loops and unnecessary duplicate packets.
* Avoiding Duplicate Packets:
* Without a designated forwarder, all PEs connected to a multihomed CE could potentially forward the same packet to the CE, resulting in duplicate packets. This duplication can cause issues with packet processing on the CE, leading to inefficiencies and potential network problems.
Conclusion:
* Option D:Correct-The designated forwarder is essential to prevent duplicate packets from being received on multihomed hosts, ensuring that only one PE forwards BUM traffic to the CE.
NEW QUESTION # 32
Exhibit.
You are troubleshooting an IP fabric (or your data center. You notice that your traffic is not being load balanced to your spine devices from your leaf devices. Referring to the configuration shown in the exhibit, what must be configured to solve this issue?
- A. The multipastmultiple -as configuration must be configured for each peer in the BGP spine group.
- B. The load-balance policy must be applied as an export policy to your BGP
- C. The load-balance policy must have a from statement that matches on protocol bgp.
- D. The load-balance policy must be applied to the forwarding table under the routing-options hierarchy.
Answer: A
Explanation:
* IP Fabric Load Balancing:
* In the provided configuration, traffic is not being load-balanced to the spine devices. The issue likely relates to how BGP routes are being selected and whether Equal-Cost Multi-Path (ECMP) is functioning correctly.
* Multipath Multiple-AS:
* Option B:The multipath multiple-as configuration is essential when using BGP in an IP fabric where devices belong to different Autonomous Systems (AS). This setting allows BGP to consider multiple paths (even across different AS numbers) as equal cost, enabling ECMP and proper load balancing across spine devices.
Conclusion:
* Option B:Correct-The multipath multiple-as configuration is necessary for achieving ECMP and effective load balancing in a multi-AS BGP environment.
NEW QUESTION # 33
Exhibit.
A VXLAN tunnel has been created between leaf1and Ieaf2 in your data center. Referring to the exhibit, which statement is correct?
- A. Traffic sent from server1to server2 will be dropped on Ieaf2.
- B. Traffic sent from server1to server2 will be tagged with VLAN ID 100 on Ieaf2 and forwarded to server2.
- C. Traffic sent from server1to server2 will be tagged with VLAN ID 200 on Ieaf2 and forwarded to server2.
- D. Traffic sent from server1to server2 will be dropped on leaf1.
Answer: C
Explanation:
* Understanding VXLAN Tunneling:
* VXLAN (Virtual Extensible LAN) is a network virtualization technology that addresses the scalability issues associated with traditional VLANs. VXLAN encapsulates Ethernet frames in UDP, allowing Layer 2 connectivity to extend across Layer 3 networks.
* Each VXLAN network is identified by a unique VXLAN Network Identifier (VNI). In this exhibit, we have two VNIs, 5100 and 5200, assigned to the VXLAN tunnels between leaf1 and leaf2.
* Network Setup Details:
* Leaf1:Connected to Server1 with VLAN ID 100 and associated with VNI 5100.
* Leaf2:Connected to Server2 with VLAN ID 200 and associated with VNI 5200.
* Spine:Acts as the interconnect between leaf switches.
* Traffic Flow Analysis:
* When traffic is sent from Server1 to Server2, it is initially tagged with VLAN ID 100 on leaf1.
* The traffic is encapsulated into a VXLAN packet with VNI 5100 on leaf1.
* The packet is then sent across the network (via the spine) to leaf2.
* On leaf2, the VXLAN header is removed, and the original Ethernet frame is decapsulated.
* Leaf2 will then associate this traffic with VLAN ID 200 before forwarding it to Server2.
* Correct Interpretation of the Exhibit:
* The traffic originating from Server1, which is tagged with VLAN ID 100, will be encapsulated into VXLAN and transmitted to leaf2.
* Upon arrival at leaf2, it will be decapsulated, and since it is associated with VNI 5200 on leaf2, the traffic will be retagged with VLAN ID 200.
* Therefore, the traffic will reach Server2 tagged with VLAN ID 200, which matches the network configuration shown in the exhibit.
* Data Center References:
* This configuration is typical in data centers using VXLAN for network virtualization. It allows isolated Layer 2 segments (VLANs) to be stretched across Layer 3 boundaries while maintaining distinct VLAN IDs at each site.
* This approach is efficient for scaling large data center networks while avoiding VLAN ID exhaustion and enabling easier segmentation.
In summary, the correct behavior, as per the exhibit and the detailed explanation, is that traffic sent from Server1 will be tagged with VLAN ID 200 when it reaches Server2 via leaf2. This ensures proper traffic segmentation and handling across the VXLAN-enabled data center network.
NEW QUESTION # 34
You are implementing seamless stitching between two data centers and have a proposedconfiguration for a border leafdevice.
In this scenario, which two statements are correct? {Choose two.)
- A. The ESI must be different in each data center.
- B. The ESI must match in both data centers.
- C. The translation-vni must be different in each data center.
- D. The translation-vni must match in both data centers.
Answer: B,C
Explanation:
* Understanding Seamless Stitching:
* Seamless stitching is used in EVPN to interconnect two data centers, allowing for consistent Layer 2 and Layer 3 connectivity across them. This is often achieved by translating VNIs (Virtual Network Identifiers) between the data centers.
* Translation-VNI:
* Option B:The translation VNI must be different in each data center to ensure that traffic can be correctly routed and distinguished as it crosses between the data centers. This differentiation helps to maintain the integrity of the traffic flows and prevents any potential overlap or conflict in VNIs.
* Ethernet Segment Identifier (ESI):
* Option D:The ESI must match in both data centers to ensure that the same Ethernet segment (which could be multihomed) is recognized consistently across the data centers. Matching ESIs are crucial for maintaining a unified view of the Ethernet segment across the interconnected fabric.
Conclusion:
* Option B:Correct-Translation VNIs must be unique to each data center for proper traffic distinction.
* Option D:Correct-Matching ESIs are necessary to maintain consistent Ethernet segment identification across both data centers.
NEW QUESTION # 35
......
JN0-683 Questions Prepare with Learning Information: https://www.suretorrent.com/JN0-683-exam-guide-torrent.html
Practice Material for JN0-683 Exam Question Preparation: https://drive.google.com/open?id=1NQ3kIH_MjGcBWeool028URxDFJ3Tjker