Free Sample Questions to Practice 1Y0-241 Certification Test Engine [Nov-2022]
2022 Valid 1Y0-241 Real Exam Questions, practice CCA-AppDS
NEW QUESTION 16
Scenario: The primary content switching vServer has gone down. To troubleshoot, a Citrix Administrator has issued the following command:
> show csvserver CSV
CSV (10.1.100.100:443) - HTTPS Type: CONTENT
State: UP
Last state change was at Mon Jun 29 15:20:43 2020
Time since last state change: 1 day, 06:47:58 610
Client Idle Timeout: 180 sec
Down state flush: ENABLED
Disable Primary vServer On Down: DISABLED
Appflow logging: ENABLED
Port Rewrite: DISABLED
State Update: DISABLED
Default: Content Precedence: URL
vServer IP and Port insertion: OFF
Persistence: NONE redirect: http://www.site1.com/mysite1/maintenance
Backup: vServer-LB-2
Listen Policy: NONE
IcmpResponse: PASSIVE
RHIstate: PASSIVE
Traffic Domain: 0
Based on this output, where will the subsequent request be redirected?
- A. Backup content switching vServer
- B. 10.1.100.100:443
- C. http://www.site1.com/mysite1/maintenance
- D. vServer-LB-2
Answer: C
NEW QUESTION 17
Scenario: The primary content switching vServer has gone down. To troubleshoot, a Citrix Administrator has issued the following command:
> show csvserver CSV
CSV (10.1.100.100:443) - HTTPS Type: CONTENT
State: UP
Last state change was at Mon Jun 29 15:20:43 2020
Time since last state change: 1 day, 06:47:58 610
Client Idle Timeout: 180 sec
Down state flush: ENABLED
Disable Primary vServer On Down: DISABLED
Appflow logging: ENABLED
Port Rewrite: DISABLED
State Update: DISABLED
Default: Content Precedence: URL
vServer IP and Port insertion: OFF
Persistence:
NONE redirect: http://www.site1.com/mysite1/maintenance
Backup: vServer-LB-2
Listen Policy: NONE
IcmpResponse: PASSIVE
RHIstate: PASSIVE
Traffic Domain: 0
Based on this output, where will the subsequent request be redirected?
- A. Backup content switching vServer
- B. 10.1.100.100:443
- C. http://www.site1.com/mysite1/maintenance
- D. vServer-LB-2
Answer: C
NEW QUESTION 18
Scenario: A Citrix Administrator made changes to a Citrix ADC, deleting parts of the configuration and saving some new ones. The changes caused an outage that needs to be resolved as quickly as possible. There is no Citrix ADC backup.
What does the administrator need to do to recover the configuration quickly?
- A. Restart the Citrix ADC.
- B. Restore from the revision history.
- C. Run saved versus running configuration.
- D. Run highly availability (HA) file synchronization.
Answer: B
NEW QUESTION 19
Scenario: A Citrix Administrator downloaded and deployed Citrix Application Delivery Management (ADM) in an environment consisting of six Citrix ADCs and 100 virtual servers. When viewing the Citrix ADM console, the administrator sees only 30 virtual servers.
Why is the administrator unable to see all 100 virtual servers?
- A. The nsroot passwords are NOT the same across all the Citrix ADCs.
- B. The Citrix ADC and Citrix ADM firmware versions are NOT the same.
- C. Additional Citrix ADM systems need to be deployed to see all virtual servers.
- D. Citrix ADM is using a free license.
Answer: C
NEW QUESTION 20
To protect an environment against Hash DoS attacks, which two configurations can a Citrix Administrator use to block all post requests that are larger than 10,000 bytes? (Choose two.)
- A. > add policy expression expr_hashdos_prevention "http.REQ.METHOD.EQ(\"POST\") ||
http.REQ.CONTENT_LENGTH.GT(10000)"
> add rewrite policy drop_rewrite expr_hashdos_prevention DROP
> bind rewrite global drop_rewrite 100 END -type REQ_OVERRIDE - B. > add policy expression expr_hashdos_prevention "http.REQ.METHOD.EQ(\"POST\") ||
http.REQ.CONTENT_LENGTH.GT(10000)"
> add responder policy pol_resp_hashdos_prevention expr_hashdos_prevention DROP NOOP
> bind responder global pol_resp_hashdos_prevention 100 END -type REQ_OVERRIDE - C. > add policy expression expr_hashdos_prevention "http.REQ.METHOD.EQ(\"POST\") ||
http.REQ.CONTENT_LENGTH.GT(10000)"
> add responder policy pol_resp_hashdos_prevention expr_hashdos_prevention DROP NOOP
> bind responder global pol_resp_hashdos_prevention 70 END -type REQ_OVERRIDE - D. > add policy expression expr_hashdos_prevention "http.REQ.METHOD.EQ(\"POST\")&&
http.REQ.CONTENT_LENGTH.GT(10000)"
> add responder policy pol_resp_hashdos_prevention expr_hashdos_prevention DROP NOOP
> bind responder global pol_resp_hashdos_prevention 70 END -type REQ_OVERRIDE - E. > add policy expression expr_hashdos_prevention "http.REQ.METHOD.EQ(\"POST\") ||
http.REQ.CONTENT_LENGTH.GT(10000)"
> add rewrite policy drop_rewrite expr_hashdos_prevention DROP
> bind rewrite global drop_rewrite 70 END -type REQ_OVERRIDE - F. > add policy expression expr_hashdos_prevention "http.REQ.METHOD.EQ(\"POST\")&&
http.REQ.CONTENT_LENGTH.GT(10000)"
> add rewrite policy drop_rewrite expr_hashdos_prevention DROP
> bind rewrite global drop_rewrite 100 END -type REQ_OVERRIDE
Answer: B,D
NEW QUESTION 21
Which Citrix ADC Access Control List (ACL) command can a Citrix Administrator use to bridge traffic originating from the IP address 192.168.10.200?
- A. add ns acl
- B. add ns simpleacl
- C. add ns acl6
- D. add ns simpleacl6
Answer: A
NEW QUESTION 22
A Citrix Administrator receives user complaints about latency while accessing an application that is load balanced on the Citrix ADC.
Which tool can the administrator use to gather information regarding response time, client network latency, and server-side processing time?
- A. Citrix Application Delivery Management (ADM)
- B. HDX Insight
- C. WAN Insight
- D. Security Insight
Answer: B
NEW QUESTION 23
Scenario: A Citrix Administrator gives permissions to team members to access their own admin partition. This will allow them to add resources for different departments and manage them without making changes to the default Citrix ADC partition and configuration.
One team member typing to use the command line interface (CLI) to troubleshoot an authentication issue could NOT use aaad.debug. However, the team member has full permissions on the admin partition.
What can be the cause of this issue?
- A. The team member is NOT using the CLI correctly.
- B. The team member needs to troubleshoot the issue from the GUI.
- C. The team member does NOT have shell access by design.
- D. The team member does NOT have permission to use the CLI.
Answer: A
NEW QUESTION 24
Scenario: A Citrix Administrator configured a responder policy as follows:
> add responder action Redirect_Act respondwith "DIAMETER.NEW_REDIRECT(\"aaa://host.example.com\")"
> add responder policy Redirect_Pol "diameter.req.avp(264).value.eq(\"host1.example.net\")" Redirect_Act
> bind lb vServer vs1 -policyName Redirect_Pol -priority 10 -type REQUEST What will be the effect of this configuration?
- A. Response originated from "host.example.net" will be redirected to "host1.example.com".
- B. Response originated from "host1.example.net" will be redirected to "host.example.com".
- C. Request originated from "host.example.net" will be redirected to "host1.example.com".
- D. Request originated from "host1.example.net" will be redirected to "host.example.com".
Answer: D
Explanation:
Explanation/Reference:
NEW QUESTION 25
Scenario: A Citrix ADC is configured with Interface 1/1 and bound to VLAN 40. A Citrix Administrator executed the below command:
> bind vlan 10 -ifnum 1/1
What is the result of executing this command on the Citrix ADC?
- A. Interface 1/1 is bound to VLAN 20, and native VLAN is NOT changed.
- B. Interface 1/1 is bound to VLAN 20, and native VLAN is 20.
- C. Interface 1/1 is bound to VLAN 20, and native VLAN is 40.
- D. Interface 1/1 is bound to VLAN 20, and native VLAN is 1.
Answer: A
Explanation:
Explanation/Reference: https://support.citrix.com/article/CTX122921
NEW QUESTION 26
Scenario: The Citrix Administrator of a Linux environment needs to load balance the web servers. Due to budget constraints, the administrator is NOT able to implement a full-scale solution.
What can the administrator purchase and install to load balance the webservers?
- A. Citrix ADC CPX
- B. Citrix ADC SDX
- C. Citrix ADC VPX
- D. Citrix ADC MPX
Answer: A
NEW QUESTION 27
A Citrix Network Engineer informs a Citrix Administrator that a data interface used by Citrix ADC SDX is being saturated.
Which action could the administrator take to address this bandwidth concern?
- A. Configure a failover interface set on each Citrix ADC VPX instance.
- B. Configure LACP on the SDX for management interface.
- C. Add a second interface to each Citrix ADC VPX instance.
- D. Configure LACP on the SDX for the data interface.
Answer: D
Explanation:
Explanation/Reference: https://training.citrix.com/public/Exam+Prep+Guides/241/1Y0-
241_Exam_Preparation_Guide_v01.pdf
NEW QUESTION 28
A Citrix Administrator configured an external syslog server but is NOT seeing detailed TCP information?
What could be causing this?
- A. Log level is NOT enabled.
- B. User-defined audit log is NOT configured.
- C. Log facility is NOT configured.
- D. TCP logging is NOT enabled.
Answer: A
NEW QUESTION 29
A Citrix Administrator needs to confirm that all client certificates presented to the authentication vServer are valid until the year 2023.
Which expression can the administrator use to meet this requirement?
- A. CLIENT.SSL.CLIENT_CERT.DAYS_TO_EXPIRE.EQ(2023)
- B. CLIENT.SSL.CLIENT_CERT.VALID_NOT_AFTER.EQ(GMT2023)
- C. CLIENT.SSL.ORIGIN_SERVER_CERT.VALID_NOT_AFTER.EQ(GMT2023)
- D. CLIENT.SSL.CLIENT_CERT.VALID_NOT_BEFORE.EQ(GMT2023)
Answer: B
Explanation:
Explanation/Reference: https://docs.citrix.com/en-us/citrix-adc/current-release/ssl/ssl-actions-and-policies/config-built-in- ssl-actions.html
NEW QUESTION 30
Scenario: A Citrix Administrator needs to improve website loading speed. End users are reporting slow GIF image rendering speeds as they scroll down a website, which affects overall page load time.
Which Citrix ADC feature can the administrator enable to improve website performance?
- A. Image lazy loading
- B. Image shrink-to attributes
- C. Image optimization
- D. Domain sharding
Answer: C
NEW QUESTION 31
Which mode does a Citrix Administrator need to configure to allow a Citrix ADC to control the packetforwarding function based on the route table lookups?
- A. Layer 3
- B. MBF
- C. Layer 2
- D. USIP
Answer: A
NEW QUESTION 32
Scenario: A Citrix Administrator needs to configure a Responder policy, so that the string "/mytraining" is added to every URL path received.
The administrator should use these commands to accomplish this:
>add responder action Redirect_Act redirect "HTTP.REQ.URL.PATH_AND_QUERY+\"mytraining\"" - responseStatusCode 302
>add responder policy Redirect_Pol___________Redirect_Act
>bind lb vServer lb_vsrv_www -policyName Redirect_Pol -priority 100 -gotoPriorityExpression END - type_______ (Choose the correct option to complete the set of commands.)
- A. "(HTTP.REQ.URL.STARTSWITH(\"mytraining\"))"
REQUEST - B. "(HTTP.REQ.URL.STARTSWITH(\"mytraining\"))"
RESPONSE - C. "!(HTTP.REQ.URL.ENDSWITH(\"mytraining\"))"
RESPONSE - D. "!(HTTP.REQ.URL.ENDSWITH(\"mytraining\"))"
REQUEST
Answer: B
NEW QUESTION 33
Scenario: A Citrix ADC is configured with Interface 1/1 and bound to VLAN 40. A Citrix Administrator executed the below command:
> bind vlan 10 -ifnum 1/1
What is the result of executing this command on the Citrix ADC?
- A. Interface 1/1 is bound to VLAN 20, and native VLAN is NOT changed.
- B. Interface 1/1 is bound to VLAN 20, and native VLAN is 20.
- C. Interface 1/1 is bound to VLAN 20, and native VLAN is 40.
- D. Interface 1/1 is bound to VLAN 20, and native VLAN is 1.
Answer: A
NEW QUESTION 34
What is the first thing a Citrix Administrator should develop when creating a server certificate for Citrix ADC to secure traffic?
- A. A certificate revocation list (CRL)
- B. A certificate key-pair
- C. A certificate signing request (CSR)
- D. A private key
Answer: D
NEW QUESTION 35
A Citrix Administrator configured global server load balancing (GSLB) for www.citrix.com, with two ADNS services named Citrix ADC 1 and Citrix ADC 2 in the setup.
Which record does the administrator need to add on the parent DNS server to delegate requests from www.citrix.com to Citrix ADC 1 and Citrix ADC 2?
- A. Name Server (NS) record
- B. Canonical Name (CNAME)
- C. Pointer Record (PTR)
- D. Address (A) record
Answer: A
Explanation:
Explanation/Reference: https://docs.citrix.com/en-us/citrix-adc/current-release/dns/configure-citrix-adc-adns-server.html
NEW QUESTION 36
Scenario: Client connections to certain vServers are abnormally high. A Citrix Administrator needs to be alerted whenever the connections pass a certain threshold.
How can the administrator use Citrix Application Delivery Management (ADM) to accomplish this?
- A. Configure SMTP reporting on the Citrix ADM by adding the threshold and email address.
- B. Configure network reporting on the Citrix ADM by setting the threshold and email address.
- C. Configure specific alerts for vServers using Citrix ADM.
- D. Configure TCP Insight on the Citrix ADM.
Answer: B
NEW QUESTION 37
Scenario: A Citrix Administrator executed the following command in a global server load balancing (GSLB) environment:
set gslb site SiteB -triggerMonitor MEPDOWN
What will be the effect of this command on the default service monitoring behavior on a remote site?
- A. The service monitor is invoked only when Metric Exchange Protocol (MEP) connectivity has been lost between Site A and Site B.
- B. The state of the GSLB service will always be controlled by Metric Exchange Protocol (MEP).
- C. The service monitor is invoked only when Metric Exchange Protocol (MEP) has marked the service as DOWN.
- D. The service monitor will take precedence over Metric Exchange Protocol (MEP).
Answer: C
NEW QUESTION 38
......
Genuine 1Y0-241 Exam Dumps Free Demo Valid QA's: https://www.suretorrent.com/1Y0-241-exam-guide-torrent.html
Latest Success Metrics For Actual 1Y0-241 Exam (Updated 65 Questions): https://drive.google.com/open?id=11Bj6Rz4T1_7GsTNN33hpA0-g3Sj7SImA